PDA

View Full Version : 60-year-old (at least) Bias Cutting Tutorial - DL



April1930s
02-08-2011, 02:31 PM
http://farm6.static.flickr. com/5098/5413675377_c78000ff0 6.jpg

60-year-old (and counting)
Bias Cutting Tutorial
with one extra, albeit important, step.... :yes:
{Courtesy of April 1930's (http://stitcheryfriend.blog spot.com/2011/02/bias-cutting-tutorial.html).}

This bias cutting technique has actually been around for quite some time. It wouldn't surprise me if it was something Mary Brooks Picken discovered all on her own when she assisted with the writing and publication of the old Singer Sewing Book. It's a simple trick, really, and makes use of small pieces for fabric conservation!

Sometimes I have a little piece of fabric leftover from a project, but not enough to cut long strips for bias trim - and it would be tedious to sew several small strips together. Other times I want to conserve every last fiber of yardage because of the fabric rarity or cost. I have a feeling I will be using this technique often for my Liberty remnant prints!

http://farm6.static.flickr. com/5256/5426072519_cd6fd0c0d 2.jpg

To begin, cut a parallelogram shape from fabric with the long sides being cut on the bias and the short sides being cut on the straight of grain.

http://farm6.static.flickr. com/5135/5426675402_02f02bdb7 2.jpg

Long sides are cut on the bias and short sides are cut on the straight of grain (as indicated by the grid on the cutting mat)

http://farm6.static.flickr. com/5180/5414285580_8d753f26e e.jpg

Accuracy is very, very important, and can make a difference in the end result, so be sure to cut the straight-grain sides and bias sides very straight like you see in the photograph above.

http://farm6.static.flickr. com/5291/5426675578_428dd08c5 3.jpg

Turn your fabric piece so that the bias edge is aligned to a straight line on the cutting mat grid and the straight-grain edge is aligned to the bias cutting line on the grid. This will allow you to draw parallel lines spaced evenly (following the straight lines on the grid) for perfectly straight bias strips... (see next photo for clarification)

http://farm6.static.flickr. com/5220/5426072673_ba15b3743 0.jpg

Now you can draw your bias lines using the measurements on your cutting mat. Whether you want bias that measures 1 inch, 1.5 inches, etc.... with a fabric marking pen, you can use the straight lines on the grid as your guide to mark parallel bias-cutting lines. (see next photo for illustration)

http://farm6.static.flickr. com/5052/5426072575_a4eb633e5 e.jpg

On the back side of the fabric piece measure and mark your bias strips to your desired width. It does not matter what width you prefer, this technique is applicable for any bias width desired.
This illustration is showing 1-inch bias being evenly lined with a fabric marking pen following the 1-inch grid lines on the cutting mat.

http://farm6.static.flickr. com/5214/5426072807_3037a0849 a.jpg

Taking the Singer Sewing Book technique one step further, on one *straight-edge side*, make a mark 1/2-inch on either the right or the left side (it doesn't matter which) of EACH bias line.

http://farm5.static.flickr. com/4142/5413674175_ac9a31158 7.jpg

In the photo above, I made my marks 1/2-inch to the left of each bias line.

http://farm6.static.flickr. com/5057/5426676064_a20b13823 e.jpg

After you make your 1/2-inch marks, transfer them to the right side of the fabric so you can easily see them when you align right sides together in the next step.

http://farm6.static.flickr. com/5172/5426073101_633e09298 b.jpg

Begin matching right sides together with the two straight-edge sides. Make sure that you have one full bias width (as indicated by the pen) that will NOT get stitched... simultaneously aligning the bias lines on one straight edge side to the 1/2-inch marks you made on the other straight edge side as you will see in the next photograph.

http://farm5.static.flickr. com/4074/5414285260_8c38d2234 e.jpg

Precisely pinning the two straight-edge sides together, align the bias lines of one straight-edge side to the 1/2-inch marks you made on the other straight-edge side. This will ensure that after stitching the two sides together, your bias lines will align straight and continuous despite the seam allowances.

http://farm6.static.flickr. com/5092/5426073229_a9129c621 5.jpg

When you bring the straight-edge sides together it will seem a bit awkward, but that is normal.

NOTE: You will need to have one full width of bias (which will NOT get stitched) on at least one end when you pin it together as indicated by the previous two pictures in the tutorial.

http://farm5.static.flickr. com/4146/5413675051_effa3263e 3.jpg

Stitch the two straight ends together using a 1/4-inch seam. Again, being precise is very important.

Notice the red stitching in the photo above? I stopped just short of the last full width of bias. There is now a full bias width that was NOT stitched as indicated in previous photo illustrations. (the extra little width on the right side is just excess and will get cut off)

http://farm6.static.flickr. com/5135/5413674879_4954d3408 9.jpg

When you align the bias lines on one side to the 1/2-inch marks you made on the other side, after stitching the right sides together, your bias lines should run in a continuous line - even through the seam you just stitched.

http://farm5.static.flickr. com/4123/5414286192_486997074 7.jpg

You can see here how the bias lines are now perfectly aligned running continuous through the seam - essentially forming a fabric tube.

Using a pressing ham or rolled towel, insert it into your fabric tube and press the seam allowances open.

http://farm5.static.flickr. com/4096/5413675115_57b1de069 c.jpg

Beginning with the side edge that has your un-stitched full-bias width, begin cutting following the bias lines you marked.

http://farm5.static.flickr. com/4116/5413675247_659544687 4.jpg

You should just keep cutting with the lines essentially forming one continuous path. Trim any excess.

My initial 8 x 18 inch fabric piece yielded 82 inches of one-inch bias!

Bias Cutting Tutorial courtesy of April 1930's (http://stitcheryfriend.blog spot.com/2011/02/bias-cutting-tutorial.html).

mommytomaddyharley
02-08-2011, 02:40 PM
Amazing!

jcsews
02-08-2011, 02:52 PM
That is mind-blowing. Wow.

Bobolots
02-08-2011, 03:18 PM
oh my goodness that is amazing. I'm a little dizzy but it was great. thanks April!!

hsmom24
02-08-2011, 03:24 PM
Fantabulous!! Thanks so much for sharing this. I normally just cut individual bias strips, and then sew them together, but this is sooo much better, and easier. :yes:

Island~mom
02-08-2011, 03:46 PM
awesome!!

sewingmel
02-08-2011, 06:32 PM
That is how I always make mine. :cheerful: Thanks for sharing.

goldencrafter
02-12-2011, 08:25 PM
Thank you for showing this it now makes sense, I am going to save a lot of time with this.

Anyamode
07-11-2013, 04:28 AM
Thank you for your tutorial

chrysalis
07-11-2013, 07:26 AM
Yea I do it that way too!!!

Helenanne
07-13-2013, 01:47 PM
I make mine in a similar way, but I start with a square, cut it into 2 triangles, stitch it into a bias parallelogram then proceed as instructed here. I get about 5 yards of double fold bias tape from a fat quarter of fabric with a 4" x 18"piece left over from making my initial square. I also do it with other size squares of fabric. You'll find similar instructions for cutting continuous bias binding in may current quilt publications.

mom2a2z
07-13-2013, 02:35 PM
Helenanne, that sounds like how I do it, too.

LawsonCrew
07-13-2013, 06:42 PM
I learned this from my grandmother (probably using the same book...) and I honestly didn't know there was another way to do it. Thanks for sharing this, April!

kellyblueyes
09-20-2013, 01:33 PM
This is brilliant! I just finished making my first bias tape and it was so very easy, I may be tempted to make something else with bias tape. Thank you! BTW I put my loop of fabric around my office chair and rolled it around while cutting it. Way easier than cutting it flat.